+-

+-User

Welcome, Guest.
Please login or register.
 
 
 
Forgot your password?

Recent Posts

Re: Bugatti Type 37 Build - remote choke by StefanN
Today at 10:46:08 am

Re: Pit Bike Wheels and tyres sets by Graham Hill
05 July 2020, 09:01:13 am

Re: Pit Bike Wheels and tyres sets by RhysN
05 July 2020, 07:41:58 am

Re: Pit Bike Wheels and tyres sets by sylvaman
04 July 2020, 10:47:39 pm

New member RichM by CKGB
04 July 2020, 08:31:36 am

Re: Bugatti Type 37 Build by Chris Brown
03 July 2020, 02:05:03 pm

Re: Bugatti Type 37 Build by RhysN
03 July 2020, 01:02:49 pm

Re: Bugatti Type 37 Build by Chris Brown
03 July 2020, 10:58:40 am

Re: Meeting Wednesday 15th July 2020. Stretton Circuit Leicester - Pre-meet 8th July 7pm by StefanN
03 July 2020, 10:42:50 am

Re: Bugatti Type 37 Build by StefanN
03 July 2020, 09:11:42 am

Top Boards

Board Topics Posts
Build journals New 21 790
Tech Forum New 92 706
Events New 42 392
Members New 90 267
Off Topic New 31 160
Where to get stuff New 25 137
For sale and wanted New 17 50
Start Here New 7 24
CK number register New 6 20
Announcements New 9 9

Top Topics

Views Replies
Dodge baquet ish build. 75022 120
Delage 15-S-8 37426 140
Article in the Parish Magazine 25026 6
Bugatti Type 37 Build 23017 126
Napier 1903 Gordon Bennett 20237 49
Whilton mill kart track practice days. 15769 31
Brakes 15403 39
Builders Meeting. Coventry Transport Museum. Saturday February 1st 2020. 14592 31
CK 1 (ERA) build 14270 53
Helping the builders who have yet to start 14154 8

Author Topic: MG 'M' Type. Brooklands 'Double 12' Racer  (Read 1674 times)

Graham Hill

  • Global Moderator
  • Full Member
  • *****
  • Posts: 199
  • Location: Leicester UK
    • View Profile
MG 'M' Type. Brooklands 'Double 12' Racer
« on: 11 January 2019, 06:39:34 pm »
I chose the MG midget 'M' type partly because it is a small car to start with and therefore would not lose proportion when reduced in size to comply with the Stevenson's guide with respect to wheelbase and track.

I purchased a junked commercial 'BIZKart' from a local circuit and was able to salvage the following components for reuse: rear 30mm axle, rear wheel hubs, locking axle spacers, driven sprocket carrier, master brake cylinder and caliper, steering column with attached pitman arm.

The engine-bolt locating locating pattern was identical for my new Loncin G200, so I cut out the relevant section of old frame and welded into my new frame to shortcut the build.
The new chassis is 75 x 25 16 gauge tube which I welded with a stick welder (not easy without blowing holes!)

The tub sides and floor are 12mm ply, the remaining sections are 4mm ply to allow bending to curve.
The bonnet, apron and skirts are covered in 1.2mm aluminum curved to shape and screw fixed directly to the ply beneath. The remainder of the ply body, including the boat tail are covered with GRP for strength utilising twill weave fabric in lieu of chopped strand mat, thereby allowing the weave to show through for a 'fabric' effect.

The wheels are from a pair of Honda 125's. They are 17" x 1.4" but heavier section steel than the C50-C90 series. The hub bearing has an OD of 40mm, which meant a selection of new bearings was readily available.

The foot-pedals are pretty simple go-kart items, bought second hand (ebay). The seat squab is from an old office chair. The steering wheel is aluminum and from an old tractor; I fabricated a spacer boss from an old brass towel rail and connected to a new quick-release hub (ebay).

Other components came new from Gemini Karts: Loncin G200 engine, Comet TAV, driven sprocket and chain, throttle cable, tie rods, axle bearings.

The springs are from Midland Motor Springs, but I ordered them 5mm thick, 4mm would have been more appropriate and others have learnt from this.

It goes and stops pretty well but I will change the current rear free-wheel set up to drive both rear wheels, this should make it more predictable when cornering hard. The engine is stock apart from the governor being removed.
The steering is very lively and I will be trying to improve this together with softening up the front springs further before another major outing.

Any questions on detailing let me know.


« Last Edit: 12 January 2019, 08:21:54 am by Graham Hill »

Share on Facebook Share on Twitter


Andy_B

  • Newbie
  • *
  • Posts: 10
  • Location: Northamptonshire
    • View Profile
Re: MG 'M' Type. Brooklands 'Double 12' Racer
« Reply #1 on: 01 June 2020, 06:56:03 pm »
Hi Graham, Just saw this - My father owns a works original MG M-type and we also used to have a C-type which as I am sure you know is the racing version!! He has had the M-type since he was 18 - so much history on it, will have to share with you some time or better still chat with my dad :)

Graham Hill

  • Global Moderator
  • Full Member
  • *****
  • Posts: 199
  • Location: Leicester UK
    • View Profile
Re: MG 'M' Type. Brooklands 'Double 12' Racer
« Reply #2 on: 02 June 2020, 09:15:51 am »
Oh, that's very interesting Andy, thanks. Let's hope things progress so we talk more soon.

Andy_B

  • Newbie
  • *
  • Posts: 10
  • Location: Northamptonshire
    • View Profile
Re: MG 'M' Type. Brooklands 'Double 12' Racer
« Reply #3 on: 02 June 2020, 10:35:56 am »
here are a couple of pics for you Graham - our old green c-type which i believe went to Germany and Dads M-type

Graham Hill

  • Global Moderator
  • Full Member
  • *****
  • Posts: 199
  • Location: Leicester UK
    • View Profile
Re: MG 'M' Type. Brooklands 'Double 12' Racer
« Reply #4 on: 02 June 2020, 12:05:40 pm »
That's so cool Andy thanks.
I was pondering whether to introduce a few improvements to the CK ....... it now appears to be a necessity!